Plates Brand New

NEW 12 to 30 ton Bushing Bearing Install Remove 10 DEEP DRIVER Set+ Press Plates

NEW 12 to 30 ton Bushing Bearing Install Remove 10 DEEP DRIVER Set+ Press Plates
NEW 12 to 30 ton Bushing Bearing Install Remove 10 DEEP DRIVER Set+ Press Plates
NEW 12 to 30 ton Bushing Bearing Install Remove 10 DEEP DRIVER Set+ Press Plates
NEW 12 to 30 ton Bushing Bearing Install Remove 10 DEEP DRIVER Set+ Press Plates
NEW 12 to 30 ton Bushing Bearing Install Remove 10 DEEP DRIVER Set+ Press Plates
NEW 12 to 30 ton Bushing Bearing Install Remove 10 DEEP DRIVER Set+ Press Plates
NEW 12 to 30 ton Bushing Bearing Install Remove 10 DEEP DRIVER Set+ Press Plates

NEW 12 to 30 ton Bushing Bearing Install Remove 10 DEEP DRIVER Set+ Press Plates

We have found a supplier of bearing drivers that don't break or deform. We offer these drivers individually or along with our Heavy Duty 20 ton press bars at a bargain price. 1 Choice for Press Accessory Solutions... Just 1 recent testimonial: Excellent quality and priceless for bearing and bushing work, how did i ever live without this set?

Replace your unsafe cast press plates and always have the right diameter bushing, bearing and seal driver at your fingertips. Each driver has a slot so you can see inside for perfect alignment to bearing or journal. Also, when pushing rubber bushings (like control arm bushings) they will expand into the driver - the slot permits easy removal of the old rubber bushing.

Have this matched set of BARS AND BEARING/BUSHING DRIVERS available for your next job. These driver sleeve OD's go all the way up to about 3.2. Seal drivers are made of plastic or aluminum and will deform when used for bearings and bushings. Our strong DEEP STEEL drivers work for all seals and bearings. Made from hardened STEEL, wall thickness is a hefty 5mm. 20 - we have never had one of our new drivers break. Yes, they are guaranteed for arbor press and hydraulic press work up to 30 tons. If a protector plate is used over the driver a hammer can be used to effectively remove and install seals and even light pressed bearings. Great for WHEEL HUB, SPINDLE, BALL JOINT, SUSPENSION BUSHING, DIFFERENTIAL work etc. You will receive 2 - 3/4" Thick X 4" RIGID X 8-1/2 long STEEL PRESS BARS, PLUS 10 DEEP Graduated Bearing DRIVERS. Bars are made in Victor, NY, USA for all Presses up to 20 Ton. BARS Will NOT "EXPLODE " Like Cast Press Plates.

If you haven't already upgraded to steel bars, now is good time. These bars are made from Prime Steel with a yield strength of well over 50,000psi. Cheaper steel has a yield strength of only 20,000psi.

Note: these drivers nest into 3 compact stacks. It would be easy to make a rack convenient to your press.

You will receive 10 NEW drivers ranging in. 34mm(1.34"), 38mm(1.5"). 42mm(1.65"), 46mm(1.81"), 50mm(1.97"), 54mm(2.13"). 58mm(2.28"), 62mm(2.44"), 66mm(2.60"), to about 70mm(2.76"). 157 bigger than internal Diameter.

Every driver is 2" deep (1.97") to receive bearing being pressed out. We often use these drivers to backup workpieces when pressing as well as removing and installing bearings in hubs and spindles.

Larger diameters are perfect for suspension bushings and larger bearings. Your bars are made from Prime Steel and may have visual surface marks that in no way impact the use to which they are intended.

These bars do not have fully ground edges and "sharp" corners like our GROUND bars do. As you probably know hot rolled steel (HR) comes in all variety of surface finishes... Our STANDARD 4 NOTCH Press X-BARS, BIG BARS and Press Plates are proudly used around the country by: Farm, Aviation, Bike, Auto and Heavy Duty shops, plus Racers, Marinas, Machine Tool, Maintenance, Industrial and Serious Hobbyists of all descriptions. Have these drivers ready for your next job. Shop Tip: For successful bearing/bushing installation, remove all rust and dirt, clean bore until smooth, lubricate bushing and bore with thin coating of Neverseeze to aid future removal.

Use these quality drivers to align bearing to bore. For rotating assemblies retaining compounds greatly improve contact area for longer life.

The item "NEW 12 to 30 ton Bushing Bearing Install Remove 10 DEEP DRIVER Set+ Press Plates" is in sale since Wednesday, December 4, 2019. This item is in the category "eBay Motors\Automotive Tools & Supplies\Shop Equipment & Supplies\Other Shop Equipment". The seller is "oldtimer1" and is located in Victor, New York. This item can be shipped to United States.

  • Manufacturer Part Number: Does Not Apply
  • Brand: Good Steel
  • Type: Press plate bar sleeve

NEW 12 to 30 ton Bushing Bearing Install Remove 10 DEEP DRIVER Set+ Press Plates